please check for usbasp firmware up date.
Thanks, AlbercookĬode: e:w:0xdd:m avrdude.exe: warning: cannot set sck period. Is that right? Do I need to do something different with the fuses? Any thoughts? I really have read up on this I'm just not understanding something in what I have read or I'm missing something.
I'm thinking that I should not have to do the 5-pin, 6-pin steps if I'm doing it this way. I tried a powered hub and the same system works fine to program a standard DigiSpark. (I had scavenged some programmed 85s form DigiSpark boards previously) When I try to program it I get the "USB Device Not Recognized" error. Finally, I soldered it onto a DIGIspark board. The chip that I bought is ATTINY85-20SH it is an 8SOIC To make contact I pressed the pins onto a little 8SOIC carrier board. I do get that warning about SCK period but don't think that is a problem. avrdude.exe: 8140 bytes of flash verified "Ifuse" memory type not defined for part "ATtiny85" avrdude.exe: safemode: Fuses OK avrdude.exe done. avrdude.exe: reading input file "DIGISPARK_FACTORY_FINAL.hex" avrdude.exe: writing flash (8140 bytes): Writing | # | 100% 3.19s avrdude.exe: 8140 bytes of flash written avrdude.exe: verifying flash memory against DIGISPARK_FACTORY_FINAL.hex: avrdude.exe: load data flash data from input file DIGISPARK_FACTORY_FINAL.hex: avrdude.exe: input file DIGISPARK_FACTORY_FINAL.hex contains 8140 bytes avrdude.exe: reading on-chip flash data: Reading | # | 100% 2.55s avrdude.exe: verifying.
avrdude.exe: erasing chip avrdude.exe: warning: cannot set sck period. avrdude.exe: AVR device initialized and ready to accept instructions Reading | # | 100% 0.03s avrdude.exe: Device signature = 0x1e930b avrdude.exe: NOTE: FLASH memory has been specified, an erase cycle will be perfo rmed To disable this feature, specify the -D option. MOSI (Pin1) from the programmer to MOSI (PB0) on the chip MISO (Pin9) from the programmer to MISO (PB1) on the chip RES (Pin5) from the programmer to RESET (PB5) on the chip SCK (Pin7) from the programmer to SCK (PB2) on the chip VCC (VTG Pin2) from the programmer to VCC on the chip GND (Pin4,6,8,10) from the programmer to GND on the chip Am I n the right track? Do I have to worry about fuse bits? Thanks, GeorgeĬode: avrdude.exe -p attin y85 -c usbasp -U flash:w:DIGISPARK_FACTORY_FINAL.hex:i -U Ifuse:w:0xe1:m -U efus e:w:0xfe:m -U hfuse:w:0x5d:m avrdude.exe: warning: cannot set sck period. If I understand correctly I need to connect as follows. If I understand this correctly ironically I'm going to use an in system programer to program chips out of my system. My board is very small and I did not have room for a jumper like JP3 on the digispark so I plan to program the chips before I solder them on my board. Now I want to built more with tiny85's from digikey that don't come with the bootloader installed.
It works when I solder on a tiny85 that I have removed form a digispark so I didn't make any critical errors. I have built a small board with a tiny85 and some additional circuity.
Install bootloader on usb password reset free#
I have been reading up in this but feel free to point out relevant posts that I may have missed. OK I think I understand what I have to to but want to run it by all you bright people.
0 kommentar(er)
